Vulcan VGC3018 User Manual

VGC SERIES GAS CONVEYOR OVENSMODELSVGC3018 ML-126196VGC3624 ML-114829VGC3632 ML-114830VGC4018 ML-126197VGC4824 ML-114831VGC4832 ML-114832VGC6024 ML-11

— 10 —PL-41123-1TIME DISPLAYTEMPERATURE DISPLAYBELT SWITCHTIME KNOBPOWER SWITCHSET POINTTIME RANGESWITCHSET POINT ARROWSCONTROL CIRCUIT FUSEDRIVE MOTO

— 11 —PL-41125-1GAS COMBINATIONCONTROL VALVEIf the burner fails to light within 90 seconds, the burner control will shut off the gas combination valve

— 12 —PL-41126-1THUMB SCREWSBAFFLETurning the Oven OffTurn Power Switch to OFF.Extended ShutdownTurn Power Switch to OFF. Turn gas combination valve

— 13 —PL-41127-1CRUMB TRAYSAir Distribution PanelsThe oven is equipped with a top and a bottom air distribution panel. These panels regulate the quan

— 14 —PL-41128-1BELT TENSION SCREWSConveyorTo maintain proper belt tension the conveyor belt will have to be adjusted to remove any slack in thebelt.1

— 15 —PL-41130PL-41129-1REMOVE COVER2. Conveyor Assembly Removala. Remove conveyor crumb trays (see Fig. 7).b. Remove cover where conveyor shaft enter

— 16 —PL-41131WeeklyCAUTION: Intake fans and slots on the back of the oven and control box must be cleanedweekly. Any obstructions may cause motor d

— 17 —CONVEYOR BELT ASSEMBLING AND DISASSEMBLING (Fig. 12)Install the conveyor belt so that it always runs inthe direction indicated by this arrow — t

— 18 —COOKING CHARTThe times and temperatures shown in this chart are suggested only. Experiment with your foodproducts to determine the cooking temp

— 19 —MAINTENANCEWARNING: THE OVEN AND ITS PARTS ARE HOT. BE VERY CAREFUL WHEN OPERATING,CLEANING OR SERVICING THE OVEN.WARNING: DISCONNECT ELECTRI

— 2 —IMPORTANT FOR YOUR SAFETYTHIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GASEQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD STAR

— 20 —FORM 31057 (5-98) PRINTED IN U.S.A.TROUBLESHOOTINGPROBLEMPower switch is on and ovenwill not operate.Burner is on but oven doesnot start.Speed c

— 3 —TABLE OF CONTENTSGENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

— 4 —Installation, Operation and Care ofMODEL VGC SERIES GAS CONVEYOR OVENSPLEASE KEEP THIS MANUAL FOR FUTURE USEGENERALVulcan ovens are produced with

— 5 —When installed, minimum clearance from combustible and non-combustible construction must be 2.5"(63.5 mm) at the sides and 2.5" (63.5 m

— 6 —PL-41122ASSEMBLYOvens Mounted on Legs or FeetTo service the oven when mounted on legs or feet, a minimum clearance of 18" (457 mm) from serv

— 7 —LEVELINGCasters for this oven are of the non-adjustable type. Therefore, the floor must be level. If floor surfaceis not level, the oven will e

— 8 —PL-41147-1TEMPERATURE DISPLAYLOAD INDICATOR LIGHTTIME DISPLAYBELT SWITCHTIME KNOBPOWER SWITCHTIME RANGESWITCHREAD SET POINT BUTTONOPERATIONWARNIN

— 9 —Belt Switch — Push switch to ON to start the conveyor belt; push to OFF to stop theconveyor belt.Power Switch — Push to ON to start the oven; pus