Vulcan G-30-O User Manual Page 1

GAS & ELECTRIC TILTING BRAISING PANSMODELG30O ML-52701G30C ML-52702G40O ML-52705G40C ML-52706E30O ML-52703E30C ML-52704E40O ML-52707E40C ML-52708V

— 10 —INSTALLATION DIAGRAM — ELECTRIC HEAT BRAISING PANSFig. 3

— 11 —OPERATIONWARNING: THE TILTING BRAISING PAN AND ITS PARTS ARE HOT. USE CARE WHENOPERATING, CLEANING OR SERVICING THE BRAISING PAN.BEFORE FIRST

— 12 —7. Lower the braising pan (see OPERATION OF LIFTING SYSTEM in this manual). The braising panwill not operate with the pan in the "up"

— 13 —DO NOT use the braising pan as a deep fat fryer, use it only for shallow pan frying (cooking oil filmnot more than 1/8" thick). Its use fo

— 14 —Do not overheat the clad stainless steel plate by setting the temperature well above recommendedtemperatures, or by operating the braising pan w

— 15 —1. Close all front doors.2. Press the upper half of the rocker switch to raise the braising pan and the lower half of the rockerswitch to lower

— 16 —STEAMING INSERTS (Optional)Your tilting braising pan can be used for steaming frozen and fresh foods. The 30-gallon pans (ModelsE or G30) can b

— 17 —CLEANINGWARNING: DISCONNECT ELECTRICAL POWER SUPPLY BEFORE CLEANING.Clean your braising pan regularly. Keep the plate surface clean. To produ

— 18 —COOKING GUIDELINESThe guidelines given below are suggested quantities, temperature settings, and estimated numbersof orders per load and per hou

— 19 —BATCHES G/E30O/C G/E40O/CPORTION TEMP. PER PER LOAD PER LOADITEM SIZE (°F) HOUR QTY. PORTIONS QTY. PORTIONSVEGETABLE

— 2 —IMPORTANT FOR YOUR SAFETYTHIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GASEQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD STAR

— 20 —BATCHES G/E30O/C G/E40O/CPORTION TEMP. PER PER LOAD PER LOADITEM SIZE (°F) HOUR QTY. PORTIONS QTY. PORTIONSCHICKENPa

— 21 —MAINTENANCEWARNING: THE TILTING BRAISING PAN AND ITS PARTS ARE HOT. USE CARE WHENOPERATING, CLEANING OR SERVICING THE BRAISING PAN.WARNING: D

— 22 —Door HingesLubricate the front door hinges with a silicone spray lubricant every 6 months. Spray the lubricant onthe hinge pin at the top and b

— 23 —TROUBLESHOOTINGGAS HEAT BRAISING PANSPROBLEMBurners do not come on.Burners produce carbon deposits.ELECTRIC HEAT BRAISING PANSPROBLEMHeating ele

— 3 —TABLE OF CONTENTSGENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

— 4 —Installation, Operation and Care ofTILTING BRAISING PANSMODELS G30O, G40O, G30C , G40C,E30O, E40O, E30C, & E40CKEEP THESE INSTRUCTIONS FOR FU

— 5 —LOCATIONFor Gas Powered Braising Pans OnlyThe braising pan must be kept free and clear of combustible substances. The braising pan, wheninstalle

— 6 —INSTALLATION CODES AND STANDARDSYour Vulcan Tilting Braising Pan must be installed in accordance with:In the United States:1. State and local cod

— 7 —SERVICE CONNECTIONSTo reach service and utility connections, remove the left side panel. To remove, hold the panel fromunderneath and lift it up

— 8 —INSTALLATION DIAGRAM — GAS HEAT BRAISING PANSFig. 2

— 9 —ELECTRICAL CONNECTIONS (see Fig. 3)WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE NATIONALELECTRICAL CODE AND/OR OTHER LOCAL