Vulcan VG30 User Manual

INSTALLATION &OPERATION MANUALFor additional information on Vulcan-Hart Company or to locate an authorizedparts and service provider in your area,

– 10 –VG30, VG40, VE30 & VE40 BRAISING PANSOPERATIONThe tilting braising pan and its parts are hot. Use care when operating, cleaningor servicing

– 11 –VG30, VG40, VE30 & VE40 BRAISING PANSLighting and Shutdown of PilotLighting instructions are also located on the front panel.1. Turn main ga

– 12 –VG30, VG40, VE30 & VE40 BRAISING PANSELECTRIC HEAT BRAISING PANSControls (see Fig. 3)Thermostat — Sets desired cooking temperature.On/Off Sw

– 13 –VG30, VG40, VE30 & VE40 BRAISING PANSFig. 4Braising Pans with Manual Lift (Standard)1. Raise the lid. The crank for the manual lift system i

– 14 –VG30, VG40, VE30 & VE40 BRAISING PANSSTEAMING INSERTS (Optional)Your tilting braising pan can be used for steaming frozen and fresh foods.

– 15 –VG30, VG40, VE30 & VE40 BRAISING PANSCLEANINGDisconnect the electrical power to the machine and followLockout / Tagout procedures before cle

– 16 –VG30, VG40, VE30 & VE40 BRAISING PANSCOOKING GUIDELINES (Domestic Measurements)The guidelines given below are suggested quantities, temperat

– 17 –VG30, VG40, VE30 & VE40 BRAISING PANSBATCHES VG30/VE30 VG40/VE40PORTION TEMP. PER PER LOAD PER LOADITEM SIZE (°F) HOUR

– 18 –VG30, VG40, VE30 & VE40 BRAISING PANSBATCHES VG30/VE30 VG40/VE40PORTION TEMP. PER PER LOAD PER LOADITEM SIZE (°F) HOUR

– 19 –VG30, VG40, VE30 & VE40 BRAISING PANSCOOKING GUIDELINES (Metric Measurements)The guidelines given below are suggested quantities, temperatur

– 2 –VG30, VG40, VE30 & VE40 BRAISING PANSIMPORTANT FOR YOUR SAFETYTHIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GASEQUIPMENT,

– 20 –VG30, VG40, VE30 & VE40 BRAISING PANSBATCHES VG30/VE30 VG40/VE40PORTION TEMP. PER PER LOAD PER LOADITEM SIZE (°C) HOUR

– 21 –VG30, VG40, VE30 & VE40 BRAISING PANSBATCHES VG30/VE30 VG40/VE40PORTION TEMP. PER PER LOAD PER LOADITEM SIZE (°C) HOUR

– 22 –VG30, VG40, VE30 & VE40 BRAISING PANSMAINTENANCEDisconnect the electrical power to the machine and followLockout / Tagout procedures before

– 23 –VG30, VG40, VE30 & VE40 BRAISING PANSTROUBLESHOOTINGGAS HEAT BRAISING PANSProblem Possible CauseBurners do not come on. 1. The power is off

– 24 –VG30, VG40, VE30 & VE40 BRAISING PANSFORM 31227 Rev A (05-08) PRINTED IN U.S.A.SERVICE AND PARTS INFORMATIONTo obtain service and parts info

– 3 –VG30, VG40, VE30 & VE40 BRAISING PANSTABLE OF CONTENTSGENERAL ...

– 4 –VG30, VG40, VE30 & VE40 BRAISING PANSInstallation, Operation and Care ofTILTING BRAISING PANSMODELS VG30, VG40, VE30 & VE40SAVE THESE INS

– 5 –VG30, VG40, VE30 & VE40 BRAISING PANSThe installation location must allow adequate clearances for servicing and proper operation.Recommended

– 6 –VG30, VG40, VE30 & VE40 BRAISING PANSINSTALLATION CODES AND STANDARDSThe Vulcan braising pan must be installed in accordance with:In the Unit

– 7 –VG30, VG40, VE30 & VE40 BRAISING PANSTESTING THE GAS SUPPLY SYSTEMWhen test pressures exceed 1/2 psig (3.45 kPa), the tilting braising pan an

– 8 –VG30, VG40, VE30 & VE40 BRAISING PANSELECTRICAL CONNECTIONS (See Fig. 2)Disconnect the electrical power to the machine and followLockout / Ta

– 9 –VG30, VG40, VE30 & VE40 BRAISING PANSINSTALLATION DIAGRAMFig. 2IMPORTANT1. A pressure regulator sized for this unit is included. Natural gas